HomeProducts & ServicesImage GalleriesOnline ServicesFriends of BeamContact

 
Products & Services » Rust Proofing » Salt & Offshore Spec 6


Coastal, Salt Mining & Offshore Rustproofing - Extreme Conditions

(Order Code:- BS6)

Beam Salt and Offshore Spec 6 is our most thorough Bituminous Based rust treatment currently available and is designed to combat corrosion in extreme conditions. BS6 includes protection of the entire external painted surfaces of the vehicle cab. This level of rust protection is suited to vehicles and machinery deployed in underground mining, salt and fertiliser works and coastal shipping facilities.

Below is a guide to a typical Application. ( Note: This may vary depending upon vehicle type )

Application Guide:

Beam ML602 upper body rust treatmentt which is a highly advanced heavy duty corrosion inhibitive wax is applied to:

  • Inside Door cavities, Pillars, Rocker Panels and Box Sections.
  • Behind headlight and grille areas
  • Inside Bonnet & Boot lid stiffeners, tailgate areas.
  • Inside Chassis rails
  • Inside Plenum Chamber.

Bituminous Black Underbody Product UB302B is typically spray applied to:
  • The complete under body and chassis
  • Lower cavities of the front and rear guards.
  • Wheel arches, fuel, air and hydraulic tanks
  • Engine Sump, Transfer casing, Drive Line,Axles and differentials.
  • Suspension components, brake housings and steering arms.
  • Fixing points for tow bars, bull bars and side steps.
  • Internal Foot wells and floor.

Ultratect “DURON" 2K Teflon/Polyurethane Chemical & Corrosion Resistant Clearcoat is typically spray applied to:
  • Underside of bonnet
  • Painted areas of the engine compartment.
  • Alloy engine components.
Beam Metal Fix 1000 Product which is a high temperature rust resistant etch primer is applied to:
  • Entire Exhaust System
Denso Tape which is a corrosion resistant wax tape is hand wrapped around the following components.
  • Front suspension rod threads, bolts, tie rods ends and top shock absorber threads.
  • Brake adjusters, line fittings, pivots.
  • All accessible hydraulic fittings and joins.
  • All external electrical wiring connections.
Ultratect "DURON" 2K Teflon/Polyurethane Clearcoat is applied to the entire exterior painted surface of the vehicle cab to a minimum 70µm DFT provide long-term protection against attack by water, acids and most chemicals. Ultratect "DURON" is clear, UV stable (will not go yellow) and will not significantly change the appearance of the substrate. It can also be removed or repaired easily at any time if required.

The vehicle is then finished by replacing all parts that were removed prior to the vehicle being protected. All drain holes are checked to ensure they are free from any residual rustproofing product. The vehicle is then cleaned off using a mild solvent to ensure that there is no over-spray on the body, trim, windows or any other exterior parts.
 

Recommended Additional Treatments

  • Ultratect “DUCOR" is a High Build 2K epoxy mastic for coating chassis and under body areas. Beam highly recommends this coating as an upgrade replacement for the traditional Bituminous Based under body coating used in this specification. See Ultratect Salt Spec 9
  • Rhino Lining Polyurethane spray-on tray and surface coating -  Ideal for load areas and to encapsulate and permanently protect high wear areas such as bull bars, side steps, internal floor pans etc... Can be sprayed on up to 6mm thick, is slip resistant, Prevents Rust and Corrosion, is waterproof and chemical resistant. 

 

 

Application Time : (6 DAYS)

(Note: The above specification was last revised 1/3/2011 and should be used as a guide only. Some procedures may be altered or omitted for specific vehicle types or due to special customer requests. Beam reserves the right to alter this specification at any time without notice if new products or techniques become available.)


Downloads

Beam is proud to be 100% Australian owned and operated Site Map | Privacy Statement | Quality Statement
Beam are proudly affiliated with